SmartDrop®

How to Measure Contact Angle: Principles and Methods

SmartDrop Applications Team, FEMTOBIOMED ·

Quick answer

Contact angle is the angle a liquid drop makes with a solid surface where liquid, solid and air meet. It shows in one number how well the surface is wetted. A contact angle goniometer photographs the drop in profile and analyzes its shape to calculate the angle.

1. What is contact angle?

Place a drop of water on a solid surface and its shape tells you about the surface. If the drop spreads out, the surface is hydrophilic (water-loving). If it beads up, the surface is hydrophobic (water-repelling).

The contact angle is the angle between the solid surface and the tangent to the liquid surface, measured through the liquid, at the three-phase contact line where solid, liquid and gas meet, that is, at the edge of the drop.

Contact angleTypical interpretation
Close to 0°Liquid spreads almost completely (complete wetting)
Below 90°Hydrophilic surface (for water)
90° or aboveHydrophobic surface (for water)
150° or aboveSuperhydrophobic surface

2. The physics behind it: Young's equation

At the edge of the drop, three interfacial tensions balance each other. Thomas Young described this balance in 1805, and it is known as Young's equation.

γSV = γSL + γLV · cos θ

  • γSV: solid–vapor interfacial tension (surface free energy of the solid)
  • γSL: solid–liquid interfacial tension
  • γLV: liquid–vapor interfacial tension (surface tension of the liquid)
  • θ: contact angle

The higher the surface free energy of the solid, the more the liquid spreads and the smaller the contact angle; the lower it is, the more the liquid beads up. That is why contact angle is the simplest and most sensitive way to check whether a surface-modifying process worked, whether it is coating, plasma treatment, cleaning or bonding preparation.

3. How is contact angle measured?

The most widely used technique is the sessile drop method.

  1. Place the sample on a level stage.
  2. Dispense a drop of fixed volume (typically a few μL) onto the sample.
  3. Backlight the drop from the side and capture its silhouette with a camera.
  4. The software detects the drop outline and the baseline, then calculates the contact angle.

There are two main ways to calculate the angle from the image.

MethodHow it worksWhat to expect
Tangent / circle fittingFits a tangent line or circle to a few points near the drop edgeFast, but results can shift with the choice of edge points and with drop size
Young–Laplace fittingFits the entire drop profile to a solution of the Young–Laplace equationAccounts for gravity-induced sagging, so it stays accurate for large or flattened drops

Small drops are nearly spherical, but as drops get larger gravity pushes them down and flattens them. Fitting a circle while ignoring this sagging introduces error into the contact angle. Young–Laplace drop shape analysis calculates the pressure inside the drop together with gravity, so this error does not arise.

SmartDrop analyzes the full drop profile in every measurement with its GEM Engine, which computes an exact numerical solution of the Young–Laplace equation with no geometric approximation. Its gravity-compensated contact angle method is protected by a Korean patent (KR 10-1935445). → How the technology works

4. Static vs. dynamic contact angle

A static contact angle is a single value measured on a drop at rest. Real surfaces, however, have roughness and chemical heterogeneity, so the angle differs depending on whether the drop is advancing over the surface or retreating from it.

  • Advancing contact angle: the maximum angle as the drop front moves forward and wets new surface
  • Receding contact angle: the minimum angle as the drop edge pulls back from the surface
  • Contact angle hysteresis: the difference between the advancing and receding angles. The smaller it is, the more easily drops roll off. For superhydrophobic, anti-fouling and anti-icing coatings, hysteresis often matters more than the static contact angle.

There are two common ways to measure dynamic contact angles.

MethodHow it worksAlso gives you
Tilting plate methodTilts the stage slowly and measures the front (advancing) and rear (receding) angles just before the drop starts to slideSliding angle (roll-off angle)
Captive drop (needle-in) methodKeeps the needle in the drop while increasing and then decreasing its volume to measure the advancing and receding anglesContact angle as a function of volume

In the tilting method, vibration during tilting can make the drop slide too early and change the result, so low-vibration motion is key to accuracy.

5. What else a contact angle goniometer measures

Because the same drop shape analysis applies, a contact angle goniometer can also measure the following.

  • Liquid surface tension: calculated by analyzing the shape of a drop hanging from a needle (pendant drop) or resting on a surface (sessile drop) with the Young–Laplace equation.
  • Solid surface free energy: calculated from contact angles of several liquids with known surface tension using a surface energy model. It helps predict how well a surface will bond, print or coat.
  • Changes over time: evaporation, absorption and spreading are analyzed from continuous image sequences. Fast events need a high-speed camera.

6. Tips for accurate measurements

  1. Keep samples clean: fingerprints, dust and organic contamination change the contact angle significantly. Handle samples with gloves and measure freshly treated samples as soon as possible.
  2. Use a constant drop volume: measure samples you want to compare with the same drop volume. Automatic dispensing is more repeatable than manual dispensing.
  3. Measure several spots: surfaces can vary from point to point, so measure multiple locations on each sample and report the mean and standard deviation.
  4. Control the timing: drops evaporate or soak in, and the angle changes. Measure at the same time after deposition every time.
  5. Record the environment: temperature, humidity and air flow affect evaporation and the measured angle. An enclosed measurement chamber with environmental logging makes results easier to compare.
  6. Get the baseline right: even a slightly misplaced baseline changes the angle. Check that the sample is level and that the baseline is detected correctly.

7. What to check when choosing a contact angle goniometer

What to checkWhy it matters
Analysis method (circle fitting / Young–Laplace)Error that depends on drop size and shape
Dynamic contact angle (tilting and captive drop)Whether you can measure hysteresis and sliding angle
Surface tension and surface free energyWhether one instrument can characterize both liquids and solids
Automatic dispensing and motorized controlVariation between operators
Camera frame rateWhether fast events such as spreading and absorption can be analyzed
Environmental control and loggingRepeatability of measurements
Publication recordWhether other labs have validated the instrument
Installation, training, support and calibrationReliable operation after purchase

8. About SmartDrop

SmartDrop is a contact angle goniometer and surface tension analyzer designed and built by FEMTOBIOMED Inc. in Korea. Since its first release in 2012, 150+ systems have been installed at universities, government research institutes and corporate R&D labs, and SmartDrop measurements have been reported in 270+ SCI(E) journal papers. → See the publication list

  • Contact angle range 1°–179°, accuracy ±0.1°
  • Low-vibration tilting over ±70° and captive drop hysteresis measurement
  • Pendant drop and sessile drop surface tension, plus surface free energy analysis
  • CORE-STD up to 200 fps; high-speed CORE-HS up to 848 fps
  • Enclosed measurement chamber with automatic temperature and humidity logging

→ View the product lineup · Request a quote or demo

Frequently asked questions

Q. Is a high contact angle good or bad?

It depends on the application. Water-repellent, anti-fouling and anti-icing coatings aim for a high contact angle and low hysteresis. Surfaces for bonding, printing or cell culture usually need a low contact angle, meaning the liquid wets them well.

Q. Which liquid should I use to measure contact angle?

Deionized (DI) water is the standard test liquid. To calculate surface free energy, you also measure with other liquids of known surface tension, such as diiodomethane and ethylene glycol.

Q. How large should the drop be?

Drops of a few microliters (μL) at a fixed volume are typical. Larger drops flatten under gravity, so instruments that use circle fitting work best with small drops. Young–Laplace fitting includes gravity in the calculation, so it is much less sensitive to drop size.

Q. Is the static contact angle enough?

For comparing a surface before and after treatment, a static contact angle is often enough. If you need to know how easily drops roll off, as with superhydrophobic or anti-fouling coatings, also measure the advancing angle, receding angle and sliding angle.

Q. Can a contact angle goniometer measure the surface tension of a liquid?

Yes. With the pendant drop method, the instrument analyzes the shape of a drop hanging from a needle tip to calculate the liquid's surface tension; an instrument used this way is often called an optical tensiometer. SmartDrop supports both pendant drop and sessile drop surface tension measurement.